Pontiac Grand Am Car Radio and Speaker Removal
	1.1) Open glove compartment, remove four screws. 1.2) Pull panel from dash releasing one clip.
	2.1) Remove three screws from panel below steering column. 2.2) Drop top edge of panel.
	3.1) Pull car stereo trim panel from dash releasing one clip.
	4.1) Loosen two bolts from top of car stereo. 4.2) Slide car stereo from dash, disconnect antenna and connectors.
Car Stereo Repair - Do It Yourself for No Display
	Pontiac Grand Am NO DISPLAY Car stereo repair, DIY.
	Pontiac Grand Am Aftermarket Car Stereo Install
	Factory Wire Color Codes See Diagram Below
	Aftermarket Wire Color Codes See Diagrams Below
	Speaker Phasing Installing Aftermarket Speakers and Proper Hook-up Speaker Phasing Font Left   Front Right + Tan   + Light green - Gray   - Dark green       Rear Left   Rear Right + Brown   + Dark blue - Yellow   - Light blue
	NO AUDIO With aftermarket stereo installation?
	Erratic Volume Control DIY Repair
Pontiac Grand Am Front Speaker Removal and Install Pontiac Grand Am How to Remove and Replace Front Speakers 1.1) Remove three screws along bottom of door panel. 2.1) Remove one screw from along back edge of door panel. 3.1) Remove one screw from door lock slide cavity. 4.1) Release door lock plastic clip from slide mechanism. 5.1) Remove insert panel over door handle. 6.1) Remove one exposed screw. 7.1) Remove one screw under arm rest. 8.1) Remove two screws from rectangular panel and remove. 9.1) Release all clips by prying along side edges of door panel. 9.2) Lift door panel up out of window jam releasing three clips. 9.3) Remove screws securing car speaker to door panel.
Pontiac Grand Am Rear Deck Speaker Removal and Install Pontiac Grand Am How to Remove and Replace Rear Speakers 1.1) Remove two bolts located at bottom edge of bottom seat cushion, each at center or both passenger positions. 2.1) Pull bottom seat cushion forward, feed seat belts through cushion. 2.2) Remove cushion. 2.3) Remove two torx bolts (#50) from center seat belts. 3.1) Lift rear seat back straight up releasing three hooks and remove. 4.1) Remove two screws along side door jam panel. 4.2) Lift door jam panel away from side of car. 5.1) With above panel loose, remove next side panel by releasing clips. 6.1) With one side panels loose and removed, pull rear deck panel forward, releasing from under opposite side. 6.2) Feed seat belts through panel and remove. 7.1) Remove screws securing speakers to  rear deck.
Pontiac Grand Am Wire Diagrams and Wire Color Codes   Wire Diagrams, Cadillac, Chevrolet, Corvette, Geo, GMC, Oldsmobile, Pontiac and Saturn. DO NOT CUT FACTORY WIRE HARNESS     Aftermarket stereo installation? Why purchase the aftermarket wire harness? Installation is easier, no guess work with wire color codes and a Headache Saver! Factory wire colors codes are not universal. See Aftermarket Videos above. We discourage cutting the factory wire harness. This section aids in troubleshooting and determining wire color codes, phasing for speaker hook up, locating power wires for installing external devices and add-ons. Diagrams may not be applicable to Bose Audio Systems     1978 - 1992 IMPORTANT - There are two (2) yellow*, two (2) gray and two (2) brown wires in this harness. Locate the +12 volt constant wire first. Label it or splice to constant wire on aftermarket stereo first. Swapping yellow wires will cause damage to any aftermarket stereo. Check fuses if your unable to find +12 volts. 1   Black Ground 2   Gray Dimmer 3   or Blank Antenna/Amplifier Trigger On 4   Yellow Switched +12 volts 5   Light Green Right Front Speaker (+) 6   Tan Left Front Speaker (+) 7   Gray Left Front Speaker (-) 8   Dark Green Right Front Speaker (-) 9   Brown Left Rear Speaker (+) 10   Dark Blue Right Rear Speaker (+) 11   Light Blue Right Rear Speaker (-) 12   Yellow Left Rear Speaker (-)     Factory Wire Harness On Factory Car Stereo   13     Orange Orange Constant +12 Volts 14     Brown Brown Illumination Corvette Only with Second One Wire Black Connector 15       Pink Bose Amplifier Trigger On     1988 - 2005 IMPORTANT - There are two (2) yellow*, two (2) gray and two (2) brown wires in this harness. Locate the +12 volt constant wire first. Label it or splice to constant wire on aftermarket stereo first. Swapping yellow wires will cause damage to any aftermarket stereo. Check fuses if your unable to find +12 volts. 1   Gray Left Front Speaker (-) 2   Tan Left Front Speaker (+) 3   Dark Green Right Front Speaker (-) 4   Light Green Right Front Speaker (+) 5   Black Ground 6   Brown Illumination 7   Gray Dimmer 8   Blank   9   Yellow* (Green) Switched +12 volts 10   Orange Constant +12 volts 11   Light Blue Right Rear Speaker (-) 12   Dark Blue Right Rear Speaker (+) 13   Yellow Left Rear Speaker (-) 14   Brown Left Rear Speaker (+)     All wire diagrams and color codes are not 100% accurate.
Car Stereo Repair Home | Car Stereo Removal | Contact | Books 4 You