How to Replace Camry Car Stereo
	Toyota Camry Removing Factory Car Stereo
	Installing Aftermarket Car Stereo
	Aftermarket Car Stereo Wire Color Codes Factory Wire Connector Codes Below
	Factory Wire Harness, Color Codes and Aftermarket Installation Factory Wire Harness Codes Below
	Speaker Phasing Installing Aftermarket Speakers and Proper Hook-up
	NO AUDIO With aftermarket stereo installation?
	Erratic Volume Control DIY Repair
Speaker Replacement, Removal and Installation Toyota Camry Front Speaker Removal and Installation 1.1) Remove two panel pins along back edge of door panel. 2.1) Remove two screw covers along front edge of door panel and remove exposed screws. 3.1) Remove screw/screws along bottom edge of door panel. 4.1) Inside side pocket, remove screw cover and remove exposed screw. 4.2) Remove screw from under arm rest. In some cases there is not a screw in this position. 5.1) Gently pry triangular panel from top of door panel starting at top edge of panel. 6.1) Gently pry control panel up, disconnect connector. 7.1) Gently pry at top edge of insert around door lock/open controls up to release latch. 8.1) Gently pry at bottom edge of insert around door lock/open controls up to release latch. 8.2) Hold door open handle out to release insert from door panel. 9.1) Gently pry tweeter speaker cover from door panel, remove exposed screw. 10.1) Remove door panel from door by starting at bottom of panel and work up both sides. 10.2) Lift door panel up out of window sill. 10.3) Disconnect connectors. 11.1) Remove screws securing car speaker to door panel. 11.2) Pull speaker from door panel and disconnect.
Replacing, Removing and Installing Speakers Toyota Camry Rear Speaker Removal and Installation 1.1) Lift front edge of rear seat up, release back edge of seat and remove seat. 2.1) Remove on bolt at base of rear seat on drivers side. 3.1) Remove on bolt at base of rear seat on passenger side. 3.2) Lift rear seat back up off of hooks and remove. 4.1) Remove third/center brake light cover. 5.1) Remove screws securing rear brake light to deck. 6.1) Disconnect connector and remove. 7.1) Remove plastic clips. 8.1) Pull pass thru seal from opening. 9.1) Pull top edge of side panel from back of car and remove, repeat for other side. 10.1) Remove two screw covers and remove exposed screws. 11.1) Pull front edge of rear deck panel forward over hooks. 12.1) Place hand inside rear brake light opening and lift up gently to clear mount while pulling entire panel toward front of car and remove. 13.1) Remove screws securing speakers. *NOTE - These are 6 3/4" speakers, we have seen a nice Pioneer speaker that fits or you may have to purchase an adaptor ring and install a 6 1/2" speaker.
Replace, Remove and Install Amplifier
	Toyota Camry How to Car Stereo Amplifier Removal and Installation Instruction Amplifier located under passenger seat.
	1.1) Push passenger seat to full back position. 1.2) Below front edge of passenger seat, disconnect two connectors at amplifier.
	2.1) Push passenger seat to full forward position and seat back forward for better access.. 2.2) Remove two mounting screws securing amplifier to floor..
	3.1) Pull car stereo amplifier from locking mount toward rear seat. *NOTE - In most cases, this amplifier is reasonably priced from the Toyota dealership.
Factory Wire Harness Codes     DO NOT CUT FACTORY WIRE HARNESS     Aftermarket stereo installation? Why purchase the aftermarket wire harness? Installation is easier, no guess work with wire color codes and a Headache Saver! Factory wire colors codes are not universal. See Aftermarket Videos above. We discourage cutting the factory wire harness. This section aids in troubleshooting and determining wire color codes, phasing for speaker hook up, locating power wires for installing external devices and add-ons.     Diagram 1   Diagram 2   Diagram 3   Diagram 4 P500 - See Factory Connectors Video above.   Diagram 5 CN701 - See Factory Connectors Video above.
Car Stereo Repair Home | Car Stereo Removal | Contact | Books 4 You